Check the rules first
Retaining walls hold back a lot of weight, and every state limits how high you can build without approval. Two examples:
- NSW: a wall can be exempt development if it's no higher than 600 mm and at least 1 m from a boundary, along with other conditions (Wollondilly Shire Council).
- Queensland: walls over 1 m need building approval, and lower walls can too, for example within 1.5 m of a building or another retaining wall (Moreton Bay City Council).
Rules differ by council and by site, so ring yours before you dig. Higher walls, steep slopes, poor soil, or a driveway or building above the wall can all mean you need an engineer.
How the calculator works it out
- Rows: standard sleepers are 200 mm high, so wall height ÷ 200, rounded up.
- Posts: one at every sleeper join, plus one at each end. For a 600 mm wall that doesn't need engineering, 2.4 m between posts is suitable.
- Post depth: retaining wall posts go half and half, as deep in the ground as the wall is high. So a 600 mm wall needs posts at least 1,200 mm long.
- Holes: at least 300 × 300 mm, dug an extra 100 mm below the post.
- Concrete: it takes 110 bags of 20 kg concrete mix to make a cubic metre. The calculator fills the whole hole, which is slightly more than you need once the post is in, so you'll have a little spare.
- Drainage: ag pipe along the back of the wall at the bottom, then drainage gravel up to 200 mm from the top, finished with soil. That's how the RIDGI concrete sleeper guide does it, with 200 mm left behind the wall for backfill.
Worked example
A straight wall 6 m long and 600 mm high, using 2.4 m sleepers:
- 600 ÷ 200 = 3 rows.
- 6 ÷ 2.4 = 2.5, so 3 bays: two full sleepers and one cut to 1.2 m in each row. That's 9 sleepers.
- 3 bays need 4 posts, each at least 1,200 mm long.
- Each hole is 300 × 300 × 700 mm, which is 0.063 m³, or 7 bags of concrete. 4 posts × 7 = 28 bags.
- Drainage gravel: 6 m long × 0.2 m wide × 0.4 m high (600 mm less the 200 mm of soil on top) = 0.48 m³.
- Ag pipe: 6 m, plus whatever it takes to run it to somewhere the water can go.
Building it
- Use concrete rated at least 25 MPa in the post holes, as the Galintel post guide specifies.
- Run a string line and keep every post the same height. Brace them while the concrete sets.
- Let the concrete cure for a couple of days before you load the posts with sleepers and soil.
- Cover the gravel with filter fabric before the soil goes on, so the drainage doesn't clog. Run the ag pipe to an outlet (Bunnings Workshop).
Common questions
How many sleepers do I need for a 10 m wall, 400 mm high?
With 2.4 m sleepers: 2 rows of 5 bays, so 10 sleepers and 6 posts. The last bay is 0.4 m, so two sleepers get cut.
How deep should retaining wall posts go?
As deep as the wall is high, plus about 100 mm under the post in the hole.
How many bags of concrete per post?
For a 300 × 300 mm hole, about one bag for every 100 mm of depth. A 700 mm hole takes 7 bags.
Do I need drainage on a small wall?
Yes. Water that builds up behind a wall pushes on it, even on a low wall, and wet soil is much heavier. Ag pipe and gravel are cheap compared to rebuilding.
This calculator is for small garden walls. It doesn't replace an engineer's design, and it can't tell you whether your wall needs approval. Your council can.
Sources
Last checked November 2026.
- Bunnings, how to build a timber retaining wall. Dig post holes as deep as the posts will stand above the ground, concrete them in, and add drainage.
- Bunnings Workshop, how deep do steel posts for a retaining wall need to be. Retaining wall posts go half and half: a 600 mm wall needs a 600 mm deep hole.
- Bunnings Workshop, retaining wall with the Retain It system. For a 600 mm wall that needs no engineering, 2400 mm between posts suits; holes at least 300 × 300 mm.
- Bunnings Workshop, retaining wall with timber sleepers and galvanised posts. Dig an extra 10 cm below the bottom of each post.
- Cement Australia, Concrete Mix product sheet. 110 × 20 kg bags of concrete mix are needed per cubic metre.
- Galintel retaining wall post selection and installation guide (Bunnings). Minimum 25 MPa concrete in post holes; check with local authorities, as height and soil can call for special designs.
- RIDGI concrete sleeper retaining wall guide (Bunnings). Leave 200 mm behind the wall; 65 mm ag pipe at the base; 20 mm drainage gravel to 200 mm from the top; clay soil plug.
- Bunnings Workshop, how to build a retaining wall. Run the drainage pipe behind the wall to an outlet, cover it with gravel, then filter fabric.
- Wollondilly Shire Council, retaining walls fact sheet. In NSW, an exempt retaining wall is no higher than 600 mm and at least 1 m from a boundary, among other rules.
- Moreton Bay City Council, retaining walls. In Queensland, walls over 1 m need building approval; lower walls can too, e.g. within 1.5 m of a building.
- Nuway Landscape Supplies, retail price list (Ormeau, March 2026). Weed mat in 1.83 × 50 m rolls; hardwood sleepers, 200 × 50 × 2400 mm.
- Bunnings, Dingo 20kg Hi Strength Concrete. Example price: $13.16 for a 20 kg bag.